3-Position Butterfly Valve
Pull lever lock, can be set to 3 different open positions
Can be cleaned in place
No pockets for particles to hide
Recommended for use on vessel outlets & fermenters
The Grainfather, is your all in one brewing system to make beer from grain. The sleek look, user friendly design, and innovative features, make this your perfect brewing companion for both experienced and beginner all grain brewers. The system features a stainless steel body and grain basket with temperature controller, recirculating pump and wort chiller.
The 8473 model is the top of the range Intertap™ Flow Control (FC) Stainless Steel model. It has all the advantages of the traditional Intertap™ design and is made from 304 grade stainless steel. In addition to this, it also had the added advantage of the flow control leaver on the right hand side of the tap. This adjustment gives the operator full control over the flow speed. This makes balancing your beer lines a snap. This type of tap is typically suited to customers who are often switching from one beer style to the next and want maximum flexibility in their draft system. The Intertap™ FC cannot be used with the shank spring so this tap should be manually turned off after use.
Typically most beer taps use a rear sealing design and the beer in the tap drains from the body of the tap with the help from a vent hole drilled at the front of the tap. This drainage hole is a dark and wet cavity and is an ideal place for airborne bacteria and wild yeast to reproduce leaving a foul film that deteriorates the quality of your beer. Every time the faucet is opened contamination occurs.
Now, when you close your Intertap™ tap, the forward sealing design shuts off the flow at the front of the tap which in turn keeps wild yeast and bacteria out of the interior of the tap body. Put end to substandard beer and only use Intertap™.
Other forward sealing designs exist but nothing with the same level of reliability. It’s easy to find other “perl” forward sealing design taps however these taps use a floating o-ring design which by all means is equally as sanitary however the floating o-ring requires the oring to move within the tap body to seal correctly. This movement is typically a problem as the tap ages and/or is not serviced regularly. Intertap™ uses a sliding shuttle that holds the o-ring perfectly in position allowing a more reliable connection to be made with the seal. This is what makes Intertap™ the most reliable forward sealing design available.
Intertap™ uses a threaded spout that can easily be removed and replaced with a range of other spouts including:
~ Stout Spout ~
~ English Sparkler Spout ~
~ Growler Filler ~
~ Ball Lock Post Spout ~
Other tap designs require you to replace the tap on the font when changing from one beer style to the next. Intertap™ allows you to simply unscrew the standard spout and attach a range of different spout options to suit your beer style. Eliminate the need to ever replace your beer taps again and simply just purchase the spouts that you need.
Note: This item is the tap only to make a complete unit you will also need to purchase a tap handle and a shank, links for these are below.
If you are storing your Series 4 Kegerator in an outdoor area where it's exposed any water, dust, or dirt we recommend you get one of our Water Resistant Covers to keep your fridge in top condition.
The cover has hot tape sealed stitching and is made from waterproof fabric so it will defend your kegerator from moisture.
The cover also has lift up panels on the sides so you can open the door without removing the entire cover.
The Micromatic Secondary Regulator is used in conjunction with your primary CO2 regulator to set individual gas pressure for an additional keg. It can handle CO2, Nitrogen, or mixed gasses, with a working pressure up to 45 PSI.
Connections are the JG push-fit style on both the inlet and outlet.
These secondary regulators are "chainable", so you can join together as many as you need, each having its own pressure. Note: you will need a blanking plug at the end of your chain. If you only have one of these secondary regulators you will still need a blanking plug. Add this to your order using the option below.
Please also note that the connection is a 3/8" push fit. Optionally select as many hose adapters to fit the 6mm gas line if you don't have 3/8" line.
Type: Secondary Regulator - CO2, N2, mixed gasses
Inlet Connection: 3/8" JG
Outlet Connection: shut-off valve + 3/8" JG
Capacity: 60 l/min maximum
Dimensions: 120 x 80 x 85mm
Max. Inlet: 7 bar / 102 PSI
Working Pressure: 0.5-3.1 bar / 45 PSI
This is a Bamboo Base Board for the MaltMuncher Grain Mill (2 Roller)
450 x 340 mm, 15mm thick
115 x 70 mm
(screw holes 140mm apart)
(requires 2x M6 bolts to mount to the two roller mill, not included)
Note: Does not include Mill
This handy pulley is made from strong polypropylene rope and heavy duty carabiner clips for a secure hold. Ideal for BIAB or to suspend the RoboBrew malt pipe. Excellent for hanging all sorts of devices.
The ratchet mechanism is easy to use and only requires single hand operation. Newer RoboBrews will have a notch for the carabiner to centre on the lifting handle, with older models these clamps or two cable ties can be used to keep it centered as shown in the photos.
10mm (3/8") Rope
113kg (250lb) weight rating
This hop tube is ideal for addling larger amounts of hop pellets or flowers to a keg or kettle. The fine mesh will prevent large particles from blocking the dip tube, pumps or chillers.
It will hold up to approximately 150g of hop pellets, allowing for some space to allow full extraction of the hop oils.
Ideal for IPA's and dry hopping in the keg, can also be used for fruits, wood chips, spices and more. Includes a small ring so it can be hung for the keg lid or side of the vessel.
Made from quality 304 Grade Stainless Steel
Tube Size: 6.6cm diameter, 29.7cm tall